Нет товаров
Цены указаны с учетом НДС
audiohobby
Lundahl Transformers is a world leading manufacturer of high performance transformers for audio applications. The company is located in the small town Norrtälje, just outside Stockholm, Sweden.
A significant difference between Lundahl Transformers and other transformer manufacturing companies is that in addition to controlling the entire manufa...
Lundahl Transformers is a world leading manufacturer of high performance transformers for audio applications. The company is located in the small town Norrtälje, just outside Stockholm, Sweden.
A significant difference between Lundahl Transformers and other transformer manufacturing companies is that in addition to controlling the entire manufacturing process (including C-cores, bobbins, pin plates and housings) we also develop and build most of our production machines.
Подкатегории
Tube amplifier output transformers
All OPTs are built in our dual coil single C-core style and can be ordered with a choice of core air-gap for Push-Pull or Single-Ended applications. Most of our OPTs can be configured for different primary and secondary impedances.
The use of C-cores with well-defined air-gap results in an almost constant inductance throughout the whole operating voltage range. For SE transformers, the primary inductance variation due to signal level is less than 7%.
Most of the transformers below are available with amorphous iron C-cores. The amorphous cores are considered to have sonic advantages, but the signal level capability with amorphous core is about 30% less than with a conventional silicon-iron C-core.
Moving coil input
Moving coil step-up transformers for impedance matching of low impedance cartridges to phono amplifiers.
Input and DC-free line output applications
Line input and line output transformers for galvanic isolation, balanced-to-unbalanced conversion and for impedance conversion. Should be used with DC-free signal sources, or with a DC blocking capacitor between source and transformer.
Anode chokes, interstage and direct couple line output transformers
Our tube amplifier transformers are built in our dual coil single C-core style and can be ordered with a choice of core air-gap for Push-Pull or Single-Ended applications.
The use of C-cores with well-defined air-gap results in an almost constant inductance throughout the whole operating voltage range. For SE transformers, the primary inductance variation due to signal level is less than 7%.
Most of the chokes and transformers below are available with amorphous iron C-cores. The amorphous cores are considered to have sonic advantages, but the signal level capability with amorphous core is about 30% less than with a conventional silicon-iron C-core.
Mains transformers
We manufacture a limited range of C-core mains transformers, primarily for tube amplifiers. Our transformers are best used with bridge rectifier circuits (four diodes), but some transformers can also be used with full wave rectifier circuits.
The hybrid power supply principle provides a bridge rectifier circuit using classical tube rectifier tubes in combination with modern diodes.
The transformer primaries are connected in series for 210 – 250V and in parallel for 105 – 125V. Secondary voltages are calculated for 230V / 115V primary voltage.
The secondary voltage listed are no-load voltage. Voltage drop because of load can be calculated from transformer copper resistance and load current. For optimal use, about 75% of power should be taken from secondary 1.
In our mains transformers, a small deliberate C-core air-gap is used to prevent from core saturation caused by any DC unbalance in the mains outlet.
Chokes for tube amp power supply or filament current supply
The ripple voltage from a rectified sinus signal, is approx. 42% of original RMS voltage.
As long as max voltage rating is not exceeded, all our power supply chokes can be used in choke input configurations.
General purpose transformers
General purpose audio transformers for ground isolation, for splitting and for balanced-to-unbalanced conversion.
General properties:
Many different connection alternatives possible
Moderate copper resistance (50 Ω per section typically)
Medium signal level capability (Max 10 dBU at 50 Hz per section typically)
Excellent magnetic and electrostatic shielding
High mu cores (mu metal or amorphous strip core)
General purpose transformers
General purpose audio transformers for ground isolation, for splitting and for balanced-to-unbalanced conversion.
General properties:
Many different connection alternatives possible
Moderate copper resistance (50 Ω per section typically)
Medium signal level capability (Max 10 dBU at 50 Hz per section typically)
Excellent magnetic and electrostatic shielding
High mu cores (mu metal or amorphous strip core)
Lundahl Silver wire Interstage transformer, LL2762Ag
Lundahl Silver wire Amorphous Core Interstage transformer, LL2762AgAM
Lundahl Amorphous Core Interstage transformer, LL2762AM
Lundahl Output transformer for headphone amplifiers, LL2765-PP
Lundahl Output transformer for headphone amplifiers, LL2765-30mA
Lundahl Output Amorphous core transformer for headphone amplifiers, LL2765AM-30mA
Lundahl Output Amorphous core transformer for headphone amplifiers, LL2765AM-PP
Lundahl Amorphous Core Interstage transformer, LL2756AM
Lundahl Silver wire Amorphous Core Line output transformer, LL1689AgAM-PP/S
DH-Labs HDMI 2.1 cable 3D/4K/8K HDR & Dolby Vision, 3.0 meter
SB Acoustics 4" mid/woofer, 25mm VC, Coaxial PAC, SB12PACR25-4-COAX...
Woofer Seas Excel excel E0091-08 W12CY006 - 1pair
REL Acoustics AirShip II Wireless extender
Resistor Jantzen Superes 1% 10W 0,27 Ohm
Resistor Jantzen Superes 1% 10W 0,22 Ohm
Resistor Jantzen Superes 1% 10W 0,18 Ohm
Resistor Jantzen Superes 1% 10W 0,12 Ohm
Wavecor silk dome tweeter TW030WA05,...