Sonnet Morpheus Digital to Analog converter with Volume control. I2S port
Warning: Last items in stock!
Pure & Simple Digital to Analog conversion with Volume control
What more can you do after launching one of the best DACs available today? The idea of having a decent volume control to prevent a analog Pre-Amplifier could improve performance dramatically. However, we also know that the way of introducing such device in the signal chain can also have a negative effect. Experiments were made and as result the best sound was coming directly from our new fully balanced dac modules. Especially in case of R2R ladder DACs it is quite easy to change the output voltage of the DAC by changing its reference voltage . The SDA-2, a new generation DAC module was designed to get the best regulation possible. The result of this process is an extremely high linearity, right down to -140 dB, which gives our products a realistic 24 bit dynamic range. It is musical, honors the Non-oversampling principle and simultaneously incorporating the technological progress that has been made over the years.
Digital to Analog Conversion with lossless volume control.The Sonnet range will gives you more weight, body, tonal richness, and a more natural sense of the space of the recording. Or to put it more plainly, it fleshes out your music more! This new range does a wonderful job of presenting even the most complex music in a natural and inviting manner with every last ounce of nuance in tact. There’s no artificial sounding edge, no sense of a flat cutout image, basically none of digital’s nastier stuff. In some cases this can also come with a somewhat dark and muddy sound but that is absolutely not the case with the new Sonnet range.It allows you to hear deep into the recording and the recording’s quality. This is somewhat of a good news/bad news proposition in that you’ll really hear what’s there.
The I2S module can be installed instead of the USB module. A new technology is used to make the I2S data format more reliable. Actually this format was made for internal use and not able to drive long data lines. Sonnet is using a kind of data transport based on the typical impedance of a standard UTP cable. By using this technology it is important that both transmitter and receiver is made for this quite heavy load of 100 Ohms. As a result lengts of 30 meters between source and receiver can be used without loss and jitter.
The I2S module is dedicated for Sonnet products like for instance our upcoming Hermes. However in some cases by removing four jumpers on top of the module it will act as a high impedance receiver and therefore more flexible to match with other products. Still Sonnet Digital Audio cannot guarantee the correct behaviour in conjunction with other systems. If you have any doubts about the correct match with our products don't hesitate to contact us.
Like the standard USB option our dacs can be ordered including the I2S module .
Balanced Non oversampling DAC
Two SDA-2 dac modules per channel in differential mode
Power supply 15VA 110/115V AC 220/230V AC 60/50Hz. Power required max 8 Watts
Input 1x optical, 1x coaxial and 1x AES/EBU and USB
Output 1x stereo pair single ended 2 Volts RMS
Output 1x stereo pair XLR balanced 4 Volts RMS
Recommended gain of used power amp in variable gain mode 22 - 26dB!
Frequency Response 44.1 kHz sampling 1Hz – 20 khz -2.5 dB
Frequency Response 192 kHz sampling 1Hz – 65 kHz – 3dB and 384kHz (USB)
Distortion 0.004% THD
Channel separation 120dB
Noise Floor -155 dB related to 2 Volt RMS
Output impedance RCA 100 Ohm, XLR 100 Ohm
Sampling rate Optical 44.1 – 96 kHz
Sampling rate Coax and AES/EBU: 44.1 -192 kHz
Sampling rate USB 44.1 – 384kHz
Aluminum six button remote control included.
MQA module (standard not included)
USB Module can be installed instead of the I2S module
free of charge.
Dimensions 290 x 250 x 60 mm
No customer reviews for the moment.